TYPE 1 LATCHES

FOR SURFACE OR
FLUSH MOUNTING


TYPE 2 LATCHES

THIN FOR MORTISING


TYPE 3 LATCHES

FLANGED FOR MORTISING


SHUTTERUP® LATCHES

hurricane shutter
latching systems


SX LATCHES

COMPACT,
STAINLESS STEEL


MIL-STD LATCHES

MIL-SPEC
5340-01-432-4353


RECEIVERS

ENCASED, NON-ENCASED


ACCESSORIES

GEARHEADS Screws,
HANDLES, KEYS


TDS 126-4 | 'U' Receiver and 'D' Receiver


‘U’ Receivers are used in many applications; they facilitate latching at 90°. Used with any Norse Latch, the aesthetic appearance of this Receiver makes it suitable for doors and other high profile applications.

The ‘D’ Receiver is a predecessor to the ‘U’ Receiver and can be used in its place. It has the advantage of providing more of a sup- port, particularly when used as a shelf or desk top attachment as shown here.


 

TDS 126-3 | 'H' Receiver and Rod Receiver


The ‘H’ Receivers were designed to be mounted behind the panel frame material, usually 3/4"/19mm wood. No flange recess is required.
‘H’ Receivers are usually used with a Type 2 or Type 3 Latch as shown here.

Rod Receivers (as shown here typically mounted in a wood 2x4 frame) have several advantages. The “setback” dimension is determined by the drill hole location, and is therefore infinitely variable, compensating for different Latch setbacks. “Press-in” installation is very simple. Various lengths are available. Cost is minimal.


 

TDS 126-2 | Non-Encased Receivers


Each of these non-encased Receivers has been designed for the numerous projects where the configuration of the elements to be joined or closed will not be accommodated otherwise.


 

TDS 126-1 | Receivers


The versatility of the Norse Latch System is to a large extent contingent upon the variety of Receivers shown on these pages, which allow the Latches to be used in so many different applications. With a few exceptions, any of these Receivers can be used with any Latch, whether the Receiver be an encased type or nonencased. Illustrations of many ‘Mixed’ combinations are shown in the ‘Applications’ of Sections 1, 2 and 3, in this catalog, and some also on the following pages.

ENCASED RECEIVERS
Type 1, Type 2, and Type 3 Encased Receivers and modifications thereof matching and interchangeable with Latches Type 1, Type 2 & Type 3.
(i.e.: A TYPE 1 LATCH CAN BE USED WITH A TYPE 2 OR TYPE 3 RECEIVERS, ETC.)


 

TDS 121-1A | Type 3R Latch and Mushroom Receiver


THIS LATCH/RECEIVER COMBINATION IS USED TO AXIALLY CLAMP TOGETHER TWO TUBES. NO RADIAL ORIENTATION IS NECESSARY. OPERATION IS BY A HEX KEY THRU A HOLE IN THE TUBE. FOR SMALLER TUBING SEE TDS 121-2


 

TDS 118-4 | Type 3 Latches • Ganged


USED FOR WIDE STRUCTURAL PANELS, EQUIPMENT ATTACHMENT, CASE CLOSURES, ETC. , WHERE MULTI-POINT SIMULTANEOUS LATCHING IS REQUIRED. MANY DIFFERENT RECEIVERS CAN BE USED.

“GANGING” NORSE LATCHES (TYPE 1, TYPE 2 AND TYPE 3) SPACED APART USES A COMMON SHAFT THRU TWO OR MORE LATCHES THAT CAN BE OPERATED FROM EITHER END OF THE SHAFT.

INSERTION OF THE SHAFT, COUPLING AND COLLARS NECESSITATES HAVING ACCESS TO THE PANEL INTERIOR BEFORE CLOSURE.


 

TDS 118-3 | Type 3 Latches • Ganged


USED FOR WIDE STRUCTURAL PANELS, EQUIPMENT ATTACHMENT, CASE CLOSURES, ETC., WHERE MULTI-POINT SIMULTANEOUS LATCHING IS REQUIRED. MANY DIFFERENT RECEIVERS CAN BE USED.

“GANGING” NORSE LATCHES (TYPE 1, TYPE 2 AND TYPE 3) SPACED APART USES A COMMON SHAFT THRU TWO OR MORE LATCHES THAT CAN BE OPERATED FROM EITHER END OF THE SHAFT.

INSERTION OF THE SHAFT/SLEEVE CAN BE DONE THRU THE ACCESS HOLE AFTER PANEL FABRICATION.


 

TDS 118-2 | Type 3 Latches • Ganged


USED FOR WIDE STRUCTURAL PANELS, EQUIPMENT ATTACHMENT, CASE CLOSURES, ETC. , WHERE MULTI-POINT SIMULTANEOUS LATCHING IS REQUIRED. MANY DIFFERENT RECEIVERS CAN BE USED.

“GANGING” NORSE LATCHES (TYPE 1, TYPE 2 AND TYPE 3) SPACED APART USES A COMMON SHAFT THRU TWO OR MORE LATCHES THAT CAN BE OPERATED FROM EITHER END OF THE SHAFT.

INSERTION OF THE SHAFT CAN BE DONE THRU THE ACCESS HOLE AFTER PANEL FABRICATION.


 

TDS 118-1 | Type 3 Latches • Ganged


USED FOR JOINING STRUCTURAL PANELS, EQUIPMENT ATTACHMENT, CASE CLOSURES, ETC. , WHERE MULTI-POINT SIMULTANEOUS LATCHING IS REQUIRED. MANY DIFFERENT RECEIVERS CAN BE USED.

“GANGING” NORSE LATCHES (TYPE 1, TYPE 2 AND TYPE 3) SPACED APART USES A COMMON SHAFT THRU TWO OR MORE LATCHES THAT CAN BE OPERATED FROM EITHER END OF THE SHAFT.

INSERTION OF THE SHAFT CAN BE DONE THRU THE ACCESS HOLE AFTER PANEL FABRICATION (SEE FIGS. 2 & 3), OR, IF THE PANEL INTERIOR IS ACCESSIBLE, ASSEMBLE THOSE ELEMENTS BEFORE PANEL CLOSURE (SEE FIGS. 1 & 4).


 

TDS 117-1A1 | Type 3 Latch and a Slot Receiver


APPLICATIONS FREQUENTLY ARISE WHERE A TYPE 3 LATCH CAN BE USED TO JOIN ONE COMPONENT TO A METAL MEMBER. A SLOT RECEIVER REALIZES SEVERAL COST AND TIME-SAVING ADVANTAGES. THE SLOT BECOMES THE RECEIVER.

THE TYPE 3 LATCH ALLOWS THE DESIGNER/FABRICATOR TO PICK THE APPROPRIATE LATCH SPRING (S1250 OR S1500) AND ‘SETBACK’ TO ACCOMMODATE EXACTLY THE REQUIREMENTS OF THE COMPONENTS BEING JOINED FOR A PERFECT FIT.


 


 

Stocking Distributor for Germany and Benelux Easy Click Systems

User login