Technical Data Sheets - Master List Type 1 Small by TDS #
Complete list of Technical Data sheets for information on specs, measurements, applications and instructions on all Norse Products
TDS 16-2A | Type 1 Small Latches
TDS 16-3 | Type 1L-Small (left hand) and Type 1L Receiver-Small
Type 1 Small Latches are used for sliding and hinged doors and panels, vehicle hoods and access panels, signs, exhibits, stage scenery, shields, cages, lighting housings, displays and show cases, valances, etc.
TDS 16-4 | TYPE 1R-SMALL (RIGHT HAND) AND TYPE 1R RECEIVER-SMALL
Type 1 Small Latches are used for sliding and hinged doors and panels, vehicle hoods and access panels, signs, exhibits, stage scenery, shields, cages, lighting housings, displays and show cases, valances, etc.
TDS 17-2A | Type 1 Small Latch with one Hub-Type Handle
TDS 17-2B | Type 1 Small Latch with Two Hub-Type Handles
TDS 17-10A | Type 1 Small Latch and H6-1 Handle Components and Mounting
Shown here is a Single Handle Mounting (Operable from one side only) with a Small Type 1L Latch surface mounted onto the door
TDS 17-10B | Type 1 Small Latch and (2) H6-1 Handles: Shaft Length and Mounting
Shown here are Two H6-1 Handles (Operable from Both Sides) with a Small Type 1L Latch Surface Mounted into the Door
TDS 18-1 | Type 1R Small Latch and "U" Receiver
This Latch/Receiver Combination is used for Joining Components at 90°
The Latch and Receiver are usually mounted on the surface. Both external and internal mountings are shown.
TDS 18-2 | Type 1R Small Latch and "D" Receiver
This Latch/Receiver Combination is used for Joining Components at 90°
The Latch and Receiver are usually mounted on the surface. Both external and internal mountings are shown.
TDS 18-3 | Type 1R Small Latch and "H" Receiver
This Latch/Receiver Combination is used for Joining Components at 90°
The Latch and Receiver are usually mounted on the surface.
TDS 19-1A | Type 1R Latch - Small Right Hand & Type "J" Receiver
The Type 1R Latch Right Hand shown, and the Type 1L Latch Left Hand (also available), are normally surface mounted; no mortising required. They may be mounted externally or internally. This Latch/Receiver combination can be used for sliding and hinged door closures, display case covers, equipment attachment, vehicle hoods, etc. See TDS 25
TDS 19-2A | Type 1R Latch - Small Right Hand and Type "JL" Receiver
The Type 1R Latch Right Hand shown, and the Type 1L Latch Left Hand (also available), are normally surface mounted; no mortising required. They may be mounted externally or internally. This Latch/Receiver combination can be used for sliding and hinged door closures, display case covers, equipment attachment, vehicle hoods, etc. See TDS 25
TDS 19-3A | Type 1L Latch - Small S1125-1L-562 and Short "P" Receiver SPR250L
This Latch/Receiver combination is particularly useful for doors, windows, boxes, furniture, case closures, access panels on machinery, hoods, etc.
TDS 19-3B | Type 1R Latch - Small S1125-1R-562 and Short "P" Receiver SPR250R
This Latch/Receiver combination is particularly useful for doors, windows, boxes, furniture, case closures, access panels on machinery, hoods, etc.
TDS 19-3C | Type 1L Latch - Small S1125-1L-562 and Short "P" Receiver SPR250L-1
This Latch/Receiver combination is particularly useful for doors, windows, boxes, furniture, case closures, access panels on machinery, hoods, etc.
TDS 19-3D | Type 1R Latch - Small S1125-1R-562 an Short "P" Receiver SPR250L-1
This Latch/Receiver combination is particularly useful for doors, windows, boxes, furniture, case closures, access panels on machinery, hoods, etc.
TDS 21-1A1 | Type 1 Small Latch and the "OT" Receiver
The "OT" Receiver has a slanted surface upon which the latch hook slides when locking, imparting a lateral force, thereby compressing the door panel against the case. This is especially beneficial when gasketing is involved. Both the "OT" and the "IT" Receivers can be used either inside or outside a case.
TDS 21-2A1 | Type 1 Small Latch and the "IT" Receiver
The "IT" Receiver has a slanted surface upon which the latch hook slides when locking, imparting a lateral force, thereby compressing the door panel against the case. This is especially beneficial when gasketing is involved. Both the "IT" and the "OT" Receivers can be used either inside or outside a case.
TDS 22-1A2 | Type 1R Small Latch and Type 2S Small RSL Receiver
For use where the Receiver is mounted flush in thin material
Blind mortise for the Receiver is only .375"/9.5mm deep.
TDS 22-1B3 | Type 1R Small Latch and Type 2 RSLS Receiver
For use where the Receiver is mounted flush in thin material
Blind mortise for the Receiver is only .437"/11.1mm deep.
TDS 22-1E | Type 1R Small Latch and Type 2S Small R/S Receiver
For use where the Receiver is mounted flush in thin material
Blind mortise for the Receiver is only .625"/16mm deep.
TDS 22-2A | Type 1R Small Latch and Type 2 RSLS Shallow Receiver
For knockdown (KD) furniture, store fixtures and other applications requiring 90° attachment, where one panel must slide freely when released
TDS 22-2B | Type 1L Small Latch and Type 2 RSLS Shallow Receiver
For knockdown (KD) furniture, store fixtures and other applications requiring 90° attachment, where one panel must slide freely when released
TDS 23-1A1 | Type 1L Small Latch and a Slot Receiver S1125-1(L or R)-562
Internally Mounted for Metal Enclosures, Cases, Doors, Access Panels, Modular Couplings, Etc.
Concealed • Protected • Aesthetically Unequaled
TDS 24-1A1 | Type 1L Small Latches/Receivers Mounted Under to Join Sectional Flooring
Shown Here Recessed Beneath Sectional Flooring, Latches are Operated with a Hex Key Thru the Floor
TDS 25-1 | Type 1 Small Sealed Latch S1125-(1R or 1L)-562S
Internally Mounted for Waterproof Enclosures, Sealed Instrument Cases, Doors, Access Panels, Etc.
TDS 25-2 | Type 1 Small Sealed Latch S1125-(1R or 1L)-562S
Internally Mounted for Waterproof Enclosures, Sealed Instrument Cases, Doors, Access Panels, Etc.
TDS 26-1A1 | Type 1 Small Latches - Ganged
"Ganged" Means Mounting Two or More Latches on a Common Shaft, Thereby Making Them Simultaneously Operable by a Single Handle or Key
TDS 27-3A1 | Type 1 Small Shroud Latch S1125-1R-562SH3
FOR SECURING A SHROUD (COVER) ON A MEDICAL UNIT, INSTRUMENT CASE, ETC.
Lever-operated from beneath with a latch mounted on both sides of the shroud (inside or outside)
TDS 28-1A1 | Type 1L Small Latches and Slot Receivers S1125-1(L or R)-562
SHOWN HERE IS JUST ONE OF SEVERAL METHODS OF FABRICATING a triangular kiosk, accent column or other angular structure using Norse Type 1 Latches (left- and right-hand). With slots cut into metal tubing to be used as receivers, any polygonal shape can be formed.
TDS 29-1A1 | Internally Flush Mounted Type 1 Latch and Shallow Type 2S RSL Receiver
The Type 1 Latch is flush mounted to the inside face of the box's front panel.
The Type 2S RSL Receiver is flush mounted to the lid's underside.